Insulation in Bedford, TX
Crawl space encapsulation and vapor barrier work in Bedford, TX almost always targets the same house: a 1960s to 1980s single-story ranch sitting on a slab or a shallow perimeter vented crawl, with settled fiberglass above and unconditioned air below. The retrofit pattern here is unlike newer suburbs because nearly every job happens inside an existing, fully built-out neighborhood where the original insulation predates Texas energy codes by decades. If you need an honest assessment of what your Bedford home actually needs, call (866) 751-4428 and a live person will answer.
Why Bedford Homes Are Different
Bedford is a fully built-out mid-cities suburb. There is essentially no undeveloped land left, which means nearly 100% of insulation work here is retrofit on homes constructed between roughly 1965 and 1990. Those houses were built to standards that would not pass a code inspection today: original fiberglass batts or thin blown-in insulation that has compressed, settled, and underperforms by a wide margin. Most Bedford attics we open sit around R-11 or below, while the current Texas code minimum is R-38. That gap is real money leaving through the ceiling every August.
Summer in Bedford means sustained stretches above 100°F, and unventilated attics in these older homes regularly reach 140°F to 160°F. HVAC systems fight that heat all season. Then winter brings periodic hard freezes and ice storms that expose the same thin walls and leaky top plates. The 1970s tract homes around the city frequently combine undersized soffit ventilation with original blown fiberglass compressed to just 3 or 4 inches. Open an attic hatch in one of those houses and you will often feel conditioned air being pulled upward, a stack-effect loss that shows up as 10% to 15% higher utility bills compared to properly insulated homes a few miles away in newer Colleyville or Southlake developments.
Our Main Bedford Services
Two services dominate the calls we take from Bedford homeowners: attic insulation and crawl space work. Here is how each one breaks down locally.
Attic Insulation in Bedford
Most Bedford attics were insulated once, when the house was built, and never touched again. The original fiberglass or blown-in material has settled decades ago and now sits well below the R-38 the Texas climate really calls for. We remove or top up that old material, air seal the floor, and bring the attic to current code. In a Bedford ranch from the 1970s, this is the single highest-ROI insulation job you can do. Find the full breakdown on our Attic Insulation in Bedford page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Crawl Space Encapsulation & Vapor Barrier in Bedford
Crawl space encapsulation in Bedford addresses a problem most homeowners in this city do not know they have: a vented crawl that pulls humid Texas air under the house every spring and summer, then leaks conditioned air out of the floor above all winter. Homes built in the 1960s through 1980s around Bedford rarely received any crawl space vapor barrier, and the ones that did got a thin 6-mil sheet that tore decades ago. The result is damp, musty crawl air migrating up into the living space, warped hardwood, and HVAC systems cycling harder than they should. This is the service we recommend Bedford homeowners consider before spending money on attic work if their floors feel cold in January or the house smells musty after rain. For the full technical breakdown, see our Crawl Space Encapsulation & Vapor Barrier service hub.
Crawl Space Vapor Barrier
Signs you need it
You notice a damp, earthy smell in the house after rain, or hardwood floors are cupping and warping even though there are no visible leaks.
What it costs in Bedford
A crawl space vapor barrier in Bedford runs roughly $2,800 to $5,500 depending on square footage and access clearance.
How we do it
We remove any old, torn plastic, level the ground where needed, and lay a new reinforced vapor barrier across the floor with overlapped seams taped and sealed. Edges run up the foundation wall and are mechanically fastened.
Crawl Space Encapsulation
Signs you need it
Your crawl space stays damp year-round, insulation under the floor is sagging or mold-stained, and your cooling bills spike every July and August.
What it costs in Bedford
Full crawl space encapsulation in Bedford typically runs $6,000 to $12,000 depending on access, existing moisture, and whether a sump pump or dehumidifier is needed.
How we do it
We seal the vents, apply a full vapor barrier to the floor and walls, insulate the perimeter, and condition the space to stop outside air from entering. A dehumidifier or sump pump is added when the existing moisture load calls for it.
What Crawl Space Encapsulation & Vapor Barrier Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Crawl space vapor barrier only | $2,800 - $5,500 |
| Full encapsulation with sealing | $6,000 - $12,000 |
| Dehumidifier (added as needed) | $1,500 - $3,000 |
Do I need a crawl space vapor barrier in Bedford if my house is on a slab?
No. Slab-on-grade homes do not have a crawl space, so they do not need a vapor barrier. Most Bedford ranch homes from the 1960s to 1980s are slab-on-grade, but a smaller subset with perimeter vented crawls absolutely benefit from encapsulation.
How long does crawl space encapsulation last in Bedford?
A properly installed encapsulation system with a sealed vapor barrier will last 25 years or more. The main variable in Bedford is groundwater and proper drainage around the foundation, so we check grading and downspout routing before sealing anything.
Spray Foam Insulation in Bedford
Spray foam insulation in Bedford is the most effective answer for two local problems: unventilated attics pushing past 150°F in summer and leaky rim joists letting conditioned air escape year-round. Older Bedford homes were built with batt insulation in exterior walls that leaves visible gaps around outlets, top plates, and rim joists, gaps you can find in minutes with a thermal camera. Closed-cell foam also adds structural rigidity, which matters on older frames that have seen decades of North Texas heat cycling. We install Spray Foam Insulation using Demilec and Icynene products, and we match the foam type to the surface rather than selling one system for every job.
Open-Cell Spray Foam
Signs you need it
Your attic is vented, your upstairs rooms run 8 to 10 degrees hotter than downstairs, and air sealing has not been done in years.
What it costs in Bedford
Open-cell spray foam for an attic in Bedford typically runs $1.50 to $2.50 per board foot, with most full attic projects landing between $3,500 and $7,500.
How we do it
We prep the attic, protect the access point, and spray an even open-cell layer to the roofline or floor. Open-cell foam expands to fill odd cavities and acts as an air barrier while stopping the stack effect.
Closed-Cell Spray Foam
Signs you need it
You have severe humidity problems, water intrusion in the crawl space, or need structural reinforcement on an older frame.
What it costs in Bedford
Closed-cell spray foam in Bedford runs $2.50 to $4.00 per board foot, with most rim joist or wall cavity jobs falling between $2,000 and $6,500.
How we do it
We apply the foam in controlled lifts to the required thickness, usually 2 inches for rim joists and 3 inches or more for roof decks. It forms a dense, moisture-resistant barrier that also stiffens the assembly.
What Spray Foam Insulation Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Open-cell attic, full roofline | $3,500 - $7,500 |
| Closed-cell rim joist package | $2,000 - $4,500 |
| Closed-cell crawl space walls | $3,000 - $6,500 |
Can you spray foam an older Bedford home without removing the old insulation?
Only if the old insulation is clean, dry, and not covering the surface to be sprayed. In most Bedford homes we remove the old fiberglass before spraying the attic floor or roofline, so the foam adheres properly and we can find the air leaks underneath.
Is spray foam worth it in Bedford when the house is already built?
Yes, and this is the standard Bedford application. Retrofit spray foam on attic rooflines and rim joists routinely cuts summer attic temperatures by 30 to 40 degrees and reduces cooling load immediately.
Blown-In Insulation in Bedford
Blown-in insulation in Bedford is usually the fastest way to bring an under-insulated attic from R-11 to R-38 in a single day. The original material in these 1960s to 1980s homes has settled and compressed to the point where it barely works. Blown-in fiberglass or cellulose can be installed over the top of existing material in many cases, or we remove the old stuff first if it is contaminated. We install Blown-In Insulation using Owens Corning and GreenFiber products, and we check ventilation and air sealing at the same time, because adding insulation over an air-leaky attic floor is wasted effort.
Blown-In Cellulose
Signs you need it
Your existing attic insulation measures 4 inches or less, or your upstairs rooms never hold temperature in winter.
What it costs in Bedford
Blown-in cellulose in a typical Bedford attic runs $1,200 to $2,800 depending on square footage and target R-value.
How we do it
We prepare the attic, install baffles where needed, and blow the cellulose to the specified depth using a calibrated machine. We measure the final depth and verify the R-value before we leave.
Blown-In Fiberglass
Signs you need it
You want a non-combustible option, or the attic has recessed can lights that need specific clearances around non-IC-rated fixtures.
What it costs in Bedford
Blown-in fiberglass in Bedford runs $1,400 to $3,200 for most single-story ranch attics, depending on depth.
How we do it
We air seal the attic floor first, then blow fiberglass to the target depth. Fiberglass resists settling better than older cellulose in high-heat attics, which matters in Bedford summers.
What Blown-In Insulation Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Blown-in cellulose, standard attic | $1,200 - $2,800 |
| Blown-in fiberglass, standard attic | $1,400 - $3,200 |
| Blown-in top-up over existing | $800 - $1,600 |
Should I remove old attic insulation before blowing in new insulation in Bedford?
Only if the old material is wet, rodent-contaminated, or compressed to the point where it cannot function. Clean, dry existing insulation can stay in place and be topped up. We inspect and tell you which route fits your attic.
How long does blown-in insulation last in a Bedford attic?
Blown-in fiberglass will last 30 or more years if it stays dry and undisturbed. Cellulose can settle 10% to 20% over time, which we account for by blowing to a higher settled depth.
Radiant Barrier Installation in Bedford
Radiant barrier installation in Bedford targets the single hottest surface in the house: the underside of the roof deck. In July and August, the roof deck on an unshaded Bedford ranch can hit 150°F or more, and that heat radiates down into the attic and through the ceiling. A foil-faced barrier stapled to the rafters reflects a large share of that radiant heat before it reaches the insulation below. It works best paired with proper attic ventilation, and we install Radiant Barrier Installation as a standalone job or alongside new insulation.
Attic Radiant Barrier
Signs you need it
Your attic is unbearable to walk into by midday in summer, or your AC runs almost continuously from June through September.
What it costs in Bedford
Attic radiant barrier for a typical Bedford attic runs $1,800 to $3,400 depending on roof geometry and access.
How we do it
We staple the foil to the underside of the rafters, leaving a small air gap at the ridge and soffits. The gap is what allows heat to escape instead of conducting through the deck.
Radiant Barrier & Ventilation
Signs you need it
You have limited soffit vents, no ridge vent, and attic temperatures that stay above 140°F after sunset.
What it costs in Bedford
Radiant barrier with a ventilation upgrade in Bedford runs $2,500 to $4,500 depending on the extent of soffit and ridge work.
How we do it
We install or upgrade the intake and exhaust vents first, then add the radiant barrier. Ventilation removes the heat the barrier reflects, so the two systems work as a pair.
What Radiant Barrier Installation Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Attic radiant barrier, standard roof | $1,800 - $3,400 |
| Radiant barrier & ventilation combined | $2,500 - $4,500 |
| Garage ceiling radiant barrier | $900 - $1,800 |
Does radiant barrier help in winter in Bedford?
Minimally. Radiant barrier works by reflecting radiant heat, which matters most in Bedford’s six-month cooling season. In winter it adds a small reflective benefit, but its primary value here is summer attic temperature reduction.
Can I install radiant barrier myself in a Bedford attic?
You can, but working on a ladder in a 140°F attic with a staple gun is genuinely dangerous. Falls and heat exhaustion are real risks. We recommend trained technicians who do it every week and know the clearance and ventilation details.
Insulation Removal & Replacement in Bedford
Insulation removal and replacement in Bedford is not optional when the existing material is rodent-contaminated, water-damaged, or compressed beyond function. Homes built in the 1960s through 1980s here often have original fiberglass or cellulose that has been soaking up dust, humidity, and animal waste for 40 or 50 years. That material cannot be topped up; it has to come out first. We handle the full removal and replacement process, and we check what is underneath while the attic is open. For the complete scope, see Insulation Removal & Replacement on our service hub.
Attic Insulation Removal
Signs you need it
Your attic insulation is matted, dusty, and settled to under 3 inches, or you can see daylight around vents and wires from inside the attic.
What it costs in Bedford
Attic insulation removal in Bedford runs $1,000 to $2,500 depending on attic size and material type.
How we do it
We use a commercial vacuum system to extract the old material through a hose, then inspect the decking and air seal the floor before new insulation goes in.
Contaminated Insulation Removal
Signs you need it
You see rodent droppings, staining, or smell a persistent ammonia odor in the attic.
What it costs in Bedford
Contaminated insulation removal in Bedford runs $1,500 to $3,500 plus sanitizing, which adds $500 to $1,200 depending on severity.
How we do it
We remove the contaminated material, sanitize the decking and framing, and treat the space before installing new insulation. We wear proper PPE through the entire process.
What Insulation Removal & Replacement Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Attic insulation removal only | $1,000 - $2,500 |
| Contaminated removal plus sanitizing | $2,000 - $4,700 |
| Full removal and new blown-in | $2,800 - $6,500 |
Do I need to remove old insulation before adding new insulation in Bedford?
Not always. If the existing material is clean, dry, and not compressed past function, we can top it up. If it is damp, rodent-contaminated, or below 3 inches in places, removal gives a better long-term result.
How long does insulation removal take in a Bedford home?
Most single-story Bedford attics take one day for removal and one day for new insulation installation. Larger or heavily contaminated attics can stretch to two or three days.
Attic Air Sealing in Bedford
Attic air sealing in Bedford stops the stack effect that pulls conditioned air out of the house through every gap in the attic floor. In these older homes, the top plates, wire penetrations, can light housings, and duct boots were never sealed, and that is why conditioned air disappears upward. Sealing those gaps before adding or upgrading insulation is the step that makes the insulation actually work. We do air sealing as part of most attic jobs, and we also do it as a standalone service. Details are on the Attic Air Sealing hub page.
Attic Floor Air Sealing
Signs you need it
Rooms directly under the attic run hotter than the rest of the house, or you feel a draft from the attic hatch in winter.
What it costs in Bedford
Attic floor air sealing in Bedford runs $900 to $2,400 depending on attic size and the number of penetrations.
How we do it
We seal every opening in the attic floor: top plates, plumbing chases, electrical penetrations, and framing joints, using foam and caulk rated for the temperature swings.
Can Light & Duct Boot Sealing
Signs you need it
You have recessed can lights in the ceiling below the attic, or supply ducts that sweat and lose temperature before air reaches the rooms.
What it costs in Bedford
Can light and duct boot sealing in Bedford runs $350 to $900 for a typical single-story house, depending on fixture count.
How we do it
We use rated covers or boxes around non-IC-rated fixtures and seal every duct boot to the floor with mastic and foam. This stops both air and heat exchange at the weakest ceiling points.
What Attic Air Sealing Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Full attic floor air sealing | $900 - $2,400 |
| Can light covers and duct boots | $350 - $900 |
| Attic hatch sealing and insulation | $150 - $350 |
How much can attic air sealing save in Bedford?
Air sealing alone typically cuts heating and cooling costs 10% to 15% in the 1960s to 1980s Bedford homes we work on. Combined with insulation, the savings are larger and more consistent across seasons.
Is attic air sealing required before new insulation in Bedford?
Not required, but strongly recommended. Adding insulation over an unsealed attic floor is like putting a heavier blanket over an open window. The insulation works, but it works much better after sealing.
Wall Insulation in Bedford
Wall insulation in Bedford is the least-visible retrofit, and the one that quietly improves winter comfort in these slab-on-grade ranches. The 1970s tract homes around the city often have minimal wall insulation, and what exists has settled or was poorly installed around outlets and framing. When a hard freeze hits North Texas, the walls show it first. We insulate existing walls without tearing out drywall, and we use Wall Insulation methods matched to the wall assembly and the era of the house. Johns Manville and Rockwool products are common on these jobs.
Injection Foam Wall Insulation
Signs you need it
Interior walls feel cold to the touch in winter, or rooms along the north and west sides never warm up evenly.
What it costs in Bedford
Injection foam wall insulation in Bedford runs $2,800 to $6,500 for a typical single-story ranch, depending on wall area.
How we do it
We drill small access points through the exterior or interior, inject foam into the wall cavities, and patch the holes. The foam expands to fill the cavity and stops air movement.
Drill & Fill Wall Insulation
Signs you need it
Your walls are hollow between studs, or you can feel drafts around electrical outlets on exterior walls.
What it costs in Bedford
Drill and fill wall insulation in Bedford runs $2,200 to $5,500 for most single-story homes.
How we do it
We drill into each stud bay, blow in the insulation to proper density, and plug the holes. We finish by matching the exterior surface, whether it is brick veneer or hardboard siding.
What Wall Insulation Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Injection foam, full exterior walls | $2,800 - $6,500 |
| Drill & fill, full exterior walls | $2,200 - $5,500 |
| Interior wall soundproofing, per room | $700 - $1,500 |
Can you insulate walls in an older Bedford home without removing drywall?
Yes. Drill and fill and injection foam are both designed for fully finished walls. We access the stud cavities from outside or inside, then patch to match. No drywall teardown is required.
How do I know if my Bedford walls already have insulation?
Pull an outlet cover and look beside the box with a flashlight, or let us check with a thermal camera during an insulation inspection. Many 1970s Bedford homes have either nothing or a thin batt that settled years ago.
Attic Cleaning & Rodent Proofing in Bedford
Attic cleaning and rodent proofing in Bedford goes hand in hand with insulation work because the same older homes that need more insulation are also the ones rats and squirrels get into. A 1970s ranch with original soffit vents and a roof that has been patched twice has entry points. Once they are in, they nest in the insulation and leave droppings through the attic. We remove the contaminated material, sanitize the space, and seal the entry points so they do not come back. The full process is on our Attic Cleaning & Rodent Proofing service page.
Attic Cleanout
Signs you need it
You see droppings or nesting material in the attic, or you hear scratching in the ceiling at night.
What it costs in Bedford
Attic cleanout in Bedford runs $800 to $2,200 depending on attic size and the extent of contamination.
How we do it
We remove all contaminated insulation and debris by vacuum, bag it for disposal, and leave the decking clean and dry before any new insulation goes in.
Rodent Proofing & Exclusion
Signs you need it
You have recurring rodent activity despite trapping, or you can see daylight through soffit gaps and roof intersections.
What it costs in Bedford
Rodent proofing and exclusion in Bedford runs $600 to $1,800 depending on the number of entry points and the materials needed.
How we do it
We seal every entry point we can find: soffit gaps, roof junctions, gable vents, and pipe penetrations. We use exclusion materials that hold up to squirrels and rats, not just caulk they can chew through.
What Attic Cleaning & Rodent Proofing Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Attic cleanout | $800 - $2,200 |
| Sanitizing and decontamination | $500 - $1,200 |
| Rodent proofing and exclusion | $600 - $1,800 |
How do rodents get into Bedford attics?
Through oof intersections, damaged soffit vents, gable vents with missing screens, and pipe penetrations. The 1960s to 1980s Bedford homes often have undersized or deteriorated soffit vents, which makes them easy entry points.
Do I need to replace insulation after rodent cleanup in Bedford?
Usually yes. Rodent waste and urine soak into the insulation and it cannot be cleaned. We remove the contaminated material, sanitize, and install fresh insulation as part of the job.
Home Energy Audit in Bedford
A home energy audit in Bedford gives you a measurable answer to one question: where is this house losing energy, and in what order should I fix it. The 1960s to 1980s housing stock here was not built to modern energy standards, so the audit usually finds multiple simultaneous problems: settled attic insulation, leaky duct boots, unsealed top plates, and underinsulated walls. We run the tests, show you the numbers, and give you a prioritized plan. Details are on the Home Energy Audit hub page.
Blower Door Test
Signs you need it
Your utility bills swing wildly between summer and winter, or the house always feels drafty no matter the thermostat setting.
What it costs in Bedford
A blower door test as part of an audit in Bedford runs $150 to $350 when bundled with the full evaluation.
How we do it
We mount a calibrated fan in an exterior door, depressurize the house, and measure the air leakage rate. That number tells us how leaky the envelope is and where those leaks are concentrated.
Thermal Imaging Inspection
Signs you need it
Some rooms are consistently hotter or colder than others, or you see cold spots on walls and ceilings in winter.
What it costs in Bedford
Thermal imaging inspection in Bedford runs $200 to $400 as part of a full home energy audit.
How we do it
We scan walls, ceilings, and floors with an infrared camera to find missing insulation, air leaks, and thermal bridging. The images give us a visual map of exactly where the house is losing energy.
What Home Energy Audit Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Full home energy audit | $400 - $800 |
| Blower door test, standalone | $150 - $350 |
| Thermal imaging inspection | $200 - $400 |
Is a home energy audit worth it in Bedford before doing insulation work?
Yes. On a house built in the 1970s, the audit finds which problem is costing you the most, so you spend money where it moves the needle. It also gives you a baseline to measure improvement after the work is done.
How long does a home energy audit take in Bedford?
Most single-story Bedford homes take 2 to 3 hours for the full audit, including the blower door test, thermal imaging, and insulation inspection. You get the report the same day or the next morning.
Brands We Service in Bedford
We install and service insulation from the manufacturers Bedford homeowners know: Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, Demilec, and GreenFiber. Material is sourced from distributor stock in the DFW metro, so standard projects start within days, not weeks. See our brands for the full manufacturer lineup.
Pricing for Insulation in Bedford, TX
| Service | Typical range in Bedford |
|---|---|
| Crawl space vapor barrier | $2,800 - $5,500 |
| Full crawl space encapsulation | $6,000 - $12,000 |
| Open-cell spray foam attic | $3,500 - $7,500 |
| Closed-cell rim joist package | $2,000 - $4,500 |
| Blown-in cellulose attic | $1,200 - $2,800 |
| Attic radiant barrier | $1,800 - $3,400 |
| Attic insulation removal | $1,000 - $2,500 |
| Full attic air sealing | $900 - $2,400 |
| Wall insulation, full exterior | $2,200 - $6,500 |
| Attic cleanout | $800 - $2,200 |
| Full home energy audit | $400 - $800 |
Prices in Bedford move up when attics are hard to access, when rodent contamination adds sanitizing steps, or when a crawl space needs drainage corrections before sealing. Every quote is upfront and fixed before we start, so you do not get a surprise change order after we open the attic.
Neighborhoods We Serve in Bedford
Bedford’s insulation retrofit work takes us across nearly every established neighborhood in the city, including:
- Shady Brook
- Harwood Terrace
- Bedford Meadows
- Stonegate
- Brookside
We can usually schedule a visit within 48 hours for standard jobs across Bedford, and emergency calls get priority same-day service when possible.
Service Area - Cities Near Bedford
Beyond Bedford, we serve the surrounding mid-cities and metro communities with the same local crew and upfront pricing model. That includes North Richland Hills, TX, Grapevine, TX, Haltom City, TX, and Grand Prairie, TX. If your home sits just over a city line, call and we will confirm coverage.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in Bedford
Standard insulation work in Bedford is usually scheduled within 48 hours. Emergency calls, like a sudden attic leak or storm damage exposing insulation, get same-day priority whenever possible. Dispatch is coordinated from our Dallas-Fort Worth office, with crews serving Bedford locally.
Most insulation retrofit work, including attic top-ups, air sealing, and spray foam, does not require a city permit. Where a job crosses into structural or ventilation changes, we check the current Bedford requirements before we start and handle the paperwork if needed.
Yes. The same upfront pricing, the same lifetime workmanship under the Done Right Promise, and the same standing offers apply: $40 off any repair over $200, a free second opinion on any written estimate, no trip charge inside the county, and 10% off for seniors and veterans, always.
For a straight answer and a real quote, call Walt’s Insulation at (866) 751-4428. A live person answers, every time.
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 30-60 min.
- 4You approve before work beginsNothing starts until you say go.
What Bedford Customers Say
"Air sealing first, then blown-in over the top. He found a bathroom fan venting straight into the attic and fixed that too. Written price before they started, same price when they finished."
- Arjun Mehta"Spray foam in the garage ceiling under the bonus room. That room used to be unusable in summer. Walt talked me out of foaming the whole attic because it did not need it - saved me a couple thousand and I trust him more for it."
- Bud Larkin"Crawl space was wet every spring. They laid the heavy liner, sealed the vents, and put a dehumidifier down there. Floors are warm and the moisture meter he left reads fine now. He still answers when I text him a reading."
- Devon Pierce