Insulation in Benbrook, TX
Most Benbrook homes need crawl space work before anything else makes sense. The combination of black gumbo clay soil, 1960s-1980s ranch construction, and decades of North Texas humidity means the crawl space under your house is quietly sabotaging every other efficiency upgrade you could make. We start there because that’s where Benbrook houses lose the most comfort per dollar. Call (866) 751-4428 and we’ll tell you exactly what’s happening under your floors before you spend a dime on anything else.
Why Benbrook Homes Are Different
Benbrook’s housing stock was built mostly between 1965 and 1985, when Fort Worth stretched west and builders put up single-story brick ranches and modest split-levels fast. Attic insulation in those homes was thin to begin with, often just a few inches of fiberglass batts. What makes Benbrook genuinely different from newer Fort Worth suburbs is what happened after construction: most of these homes sit on expansive black gumbo clay that shrinks and swells with every wet-dry cycle. Over 40 or 50 years, that subtle movement shifts rim joists and wall plates, opening gaps where batt insulation separates from framing. You can’t see those gaps, but a blower door test finds them in nearly every older ranch we inspect here. Add in IECC Climate Zone 3 summers that sit above 100°F for weeks and Blue Norther cold snaps in January, and one insulation system has to fight heat gain in July and heat loss in February. Winter Storm Uri in 2021 made that obvious to a lot of Benbrook homeowners who’d never thought about R-values before.
Our Main Benbrook Services
These are the two services Benbrook homeowners call about most often, and they share a common thread: both are invisible problems until they aren’t. Here’s what each one actually involves in a Benbrook house.
Attic Insulation in Benbrook
Most Benbrook attics were insulated once, when the house was built, and never touched again. That means R-19 or less in a climate that wants R-38 to R-60, and an attic full of compressed, settled fiberglass that isn’t doing its job. We remove the old material when it’s contaminated, air-seal the attic floor, and blow in fresh insulation to current Climate Zone 3 standards. In Benbrook’s older ranch homes, the payoff shows up in July, when the upstairs stops feeling like a different climate zone than the rest of the house. Read more about how we handle this work on our Attic Insulation in Benbrook page.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Crawl Space Encapsulation & Vapor Barrier in Benbrook
Crawl space encapsulation in Benbrook is the single highest-impact upgrade for older ranch homes here. The black gumbo clay under your house holds moisture, and that moisture migrates up through the soil into the crawl space, where it meets warm air and turns into humidity, mold, and rot. In a 1970s split-level or ranch with a vented crawl space, our Crawl Space Encapsulation & Vapor Barrier process seals the entire space, stops the moisture at the source, and turns the lowest part of your house into the driest part of it.
Crawl Space Vapor Barrier
Signs you need it
You smell a musty odor in rooms above the crawl space, or you’ve seen condensation on ductwork in the crawl space during Benbrook’s humid spring and fall months.
What it costs in Benbrook
A crawl space vapor barrier in Benbrook typically runs $1,200-$3,500 depending on square footage and access.
How we do it
We lay a heavy-duty reinforced polyethylene liner across the entire crawl space floor, lap the seams, and secure it to the foundation walls so ground moisture can’t wick through.
Crawl Space Encapsulation
Signs you need it
Standing water or damp soil after rain, visible mold on floor joists, or humidity readings above 60% inside the crawl space.
What it costs in Benbrook
Full crawl space encapsulation in Benbrook generally falls between $5,000 and $12,000, with larger or tighter crawl spaces at the upper end.
How we do it
We seal all vents, install the vapor barrier up the walls, add a drainage mat where needed, and install a dehumidifier sized for the square footage.
Crawl Space Insulation
Signs you need it
Cold floors in winter despite a running furnace, or HVAC bills that spike every January and July in Benbrook.
What it costs in Benbrook
Crawl space insulation in Benbrook typically costs $800-$2,500 for the full space, depending on whether we use fiberglass batts, rockwool, or closed-cell foam on the rim joists.
How we do it
We insulate the rim joist bays and foundation walls rather than the floor itself in most cases, which keeps the mechanicals inside the conditioned space.
What Crawl Space Encapsulation & Vapor Barrier Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Vapor barrier only | $1,200 - $3,500 |
| Full encapsulation | $5,000 - $12,000 |
| Crawl space insulation | $800 - $2,500 |
| Dehumidifier addition | $1,500 - $3,000 |
Does crawl space encapsulation help with Benbrook’s humidity?
Yes, significantly. Sealing the crawl space stops ground moisture from entering the home at all, which drops indoor humidity in the living areas above it and takes pressure off your AC in July and August. Most Benbrook homeowners notice the difference within the first week.
Will encapsulation fix my cold floors in winter?
Usually, because you’re stopping cold outside air from flowing through the crawl space and under your floors. Combined with rim joist insulation, encapsulation can raise floor temperatures in a Benbrook ranch by several degrees. Call (866) 751-4428 for a free second opinion on any written estimate you’ve received.
Spray Foam Insulation in Benbrook
Spray foam in Benbrook solves a problem that’s built into the housing stock: retrofitted HVAC equipment and decades of air leakage in those open attic cavities. Because Benbrook homes were built before modern air-sealing practices, the attics leak like sieves, and batt insulation alone can’t stop conditioned air from escaping. Our Spray Foam Insulation work seals the building envelope itself, not just the insulation layer.
Open-Cell Spray Foam
Signs you need it
Rooms that never hold temperature, especially rooms over a garage or at the end of a duct run, and you hear outdoor noise through the ceiling.
What it costs in Benbrook
Open-cell spray foam in Benbrook runs $1.50-$3.50 per board foot installed, with typical attic applications landing between $3,000 and $7,000 for a 1,500-square-foot ranch.
How we do it
We spray the foam directly onto the underside of the roof deck, creating an air barrier and thermal barrier in one pass that reaches the R-38 to R-60 range with enough thickness.
Closed-Cell Spray Foam
Signs you need it
A crawl space that stays damp even after vapor barrier work, or a Benbrook home where the rim joists show gaps from decades of clay soil movement.
What it costs in Benbrook
Closed-cell spray foam in Benbrook typically costs $3.50-$7.00 per board foot installed.
How we do it
We apply closed-cell foam to rim joist bays and crawl space walls, where it acts as both insulation and moisture barrier in a single application.
What Spray Foam Insulation Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Open-cell attic spray foam | $3,000 - $7,000 |
| Closed-cell rim joist spray foam | $1,500 - $4,000 |
| Garage ceiling spray foam | $1,800 - $4,500 |
| Spray foam roof deck | $4,000 - $9,000 |
Is spray foam worth it in a Benbrook ranch home?
For homes with HVAC in the attic, yes, because the ductwork sits inside the conditioned envelope once the roofline is foamed. That eliminates the duct losses that plague older Benbrook homes with 1990s retrofitted air handlers. It’s the most expensive option, but the monthly utility reduction is real.
Can you spray foam over old insulation?
No, old fiberglass or cellulose has to come out first. Foam needs direct contact with the roof deck or wall sheathing to form a proper air seal. Call (866) 751-4428 and we’ll walk you through the removal cost as part of the quote.
Blown-In Insulation in Benbrook
Blown-in insulation is the most common upgrade we do in Benbrook attics, mostly because it’s the fastest way to bring a 1970s ranch up to modern R-value without tearing anything apart. In a Benbrook home with open attic cavities and minimal existing insulation, Blown-In Insulation solves the single biggest energy leak: heat pouring through the ceiling in July and escaping the same way in January.
Blown-In Cellulose
Signs you need it
Your attic has less than 6 inches of old, settled insulation, and your upstairs rooms feel 10 degrees warmer than the rest of the house in summer.
What it costs in Benbrook
Blown-in cellulose in a Benbrook attic typically runs $1.00-$2.00 per square foot installed, so a 1,500-square-foot attic lands around $1,500-$3,000.
How we do it
We air-seal the attic floor first, then blow GreenFiber cellulose to the target depth for R-38 to R-60, making sure the soffit vents stay clear for airflow.
Blown-In Fiberglass
Signs you need it
You want to upgrade attic insulation and prefer a material that won’t settle as much over time, especially in a Benbrook home where HVAC equipment makes attic access tight.
What it costs in Benbrook
Blown-in fiberglass in Benbrook runs $1.20-$2.50 per square foot installed, with most ranch-style attics falling between $1,800 and $3,750.
How we do it
We blow Owens Corning fiberglass to the same R-38 to R-60 target, using a dense-blow setting where we can reach the far edges of the attic.
What Blown-In Insulation Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Blown-in cellulose (attic) | $1,500 - $3,000 |
| Blown-in fiberglass (attic) | $1,800 - $3,750 |
| Blown-in top-up over existing insulation | $800 - $1,800 |
| Dense-pack wall insulation | $2,500 - $6,000 |
How much insulation does a Benbrook attic need?
Current Climate Zone 3 code wants R-38 to R-60 in the attic. Most Benbrook homes built in the 1960s through 1980s have R-11 to R-19, so they’re less than halfway to minimum. We measure what’s there and tell you exactly how many inches to add.
Is blown-in better than batts for an older Benbrook house?
Usually yes, because blown-in fills irregular cavities and settles around the framing and retrofitted HVAC equipment that batt installation in these older homes is simply unable to properly cover. Call (866) 751-4428 for a straight answer about your specific attic.
Radiant Barrier Installation in Benbrook
Radiant barrier in Benbrook targets the specific misery of August: the sun beating on your roof deck and turning your attic into an oven. In a single-story ranch with a large open attic cavity, that heat radiates down into the living space all afternoon. Our Radiant Barrier Installation work reflects that heat before it gets inside, cutting attic temperatures by as much as 30°F during peak load.
Attic Radiant Barrier
Signs you need it
Your AC runs nonstop from 2 PM to 8 PM in July, and the ceiling feels warm to the touch in the afternoon even though the thermostat says it’s 78.
What it costs in Benbrook
An attic radiant barrier in Benbrook typically runs $1,200-$3,000 for a standard single-story ranch, depending on attic size and access.
How we do it
We staple a reinforced foil radiant barrier to the underside of the roof rafters, leaving an air gap that allows the foil to reflect heat back out through the roof.
Radiant Barrier Foil
Signs you need it
Your attic insulation is adequate but the house still bakes in the afternoon, which tells us radiant heat, not conduction, is the primary problem.
What it costs in Benbrook
Radiant barrier foil installation in Benbrook runs $0.50-$1.25 per square foot of attic floor area, so most homes here fall between $800 and $2,500.
How we do it
We lay the foil directly over the attic floor insulation, which works best in Benbrook homes where the attic is only used for storage and stays dry.
What Radiant Barrier Installation Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Attic radiant barrier | $1,200 - $3,000 |
| Radiant barrier foil over insulation | $800 - $2,500 |
| Radiant barrier on roof deck | $1,500 - $3,500 |
Does radiant barrier do anything in winter?
Less than in summer, but it isn’t worthless. The same reflective surface that rejects July heat also helps hold heat inside during January cold snaps, acting as a low-emissivity surface that slows radiant loss. In Benbrook, the summer benefit is the reason to install it.
Can I add radiant barrier to a house with spray foam?
No, and you wouldn’t want to. Spray foam already handles heat transfer differently, and a radiant barrier needs an air gap to work. We’ll tell you which approach makes sense for your Benbrook home before quoting anything. Call (866) 751-4428.
Insulation Removal & Replacement in Benbrook
Insulation removal in Benbrook is usually driven by one of three things: rodent or raccoon contamination, decades of dust and debris in an attic where HVAC was retrofitted, or the 2021 freeze that soaked insulation when pipes burst above ceilings. In older ranch homes here, Insulation Removal & Replacement isn’t a luxury; it’s how you make sure the new insulation doesn’t sit on top of a contaminated mess.
Attic Insulation Removal
Signs you need it
You see rodent droppings throughout the attic, or the insulation is compacted, dark, and clearly no longer performing as it once did.
What it costs in Benbrook
Attic insulation removal in Benbrook typically runs $1.00-$2.00 per square foot, so a 1,500-square-foot attic falls between $1,500 and $3,000.
How we do it
We vacuum out the old material with commercial equipment, bag it, and prep the attic for new insulation without dragging contaminants through your living space.
Contaminated Insulation Removal
Signs you need it
A bat infestation left guano throughout the attic, or a family of squirrels nested in the insulation and left feces and urine you can smell from the hallway.
What it costs in Benbrook
Contaminated insulation removal in Benbrook starts at $2,000 and can run up to $6,000 depending on the extent of contamination and attic size.
How we do it
We remove the contaminated material under containment, sanitize the affected framing, and only then install fresh insulation that won’t re-contaminate.
What Insulation Removal & Replacement Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Standard attic insulation removal | $1,500 - $3,000 |
| Contaminated insulation removal | $2,000 - $6,000 |
| Insulation replacement (removal + new) | $3,000 - $7,500 |
| Vermiculite removal | $4,000 - $10,000 |
How do I know if my Benbrook insulation needs removal?
If you can see rodent trails, smell animal waste, or the insulation is visibly compacted and dark, it should come out. Reinsulating over contaminated material just seals the problem in. Most Benbrook homeowners only find this out after we pull back the access hatch and look.
Do you remove old insulation before blowing in new?
Only when the old material is contaminated or too compressed to add onto. Otherwise, we can often blow new insulation right over the top and reach the R-value you need for less money. Call (866) 751-4428 for a straight answer on your attic.
Attic Air Sealing in Benbrook
Attic air sealing in Benbrook addresses the invisible leak channels created by decades of clay soil movement in these older ranch and split-level homes. As the ground under your house expands and contracts through wet and dry cycles, gaps open around top plates, wire penetrations, and can lights, allowing conditioned air to escape into the attic. Our Attic Air Sealing work closes those gaps before any insulation goes in.
Attic Floor Air Sealing
Signs you need it
Your upstairs rooms won’t hold temperature, and you can feel drafts near light fixtures and ceiling fans in winter.
What it costs in Benbrook
Attic floor air sealing in Benbrook typically runs $1,000-$2,500 for a standard single-story home, depending on the number of penetrations.
How we do it
We pull back the existing insulation, seal every crack and gap in the attic floor with foam and caulk, and then reinstall or replace the insulation.
Top Plate & Penetration Sealing
Signs you need it
You see dirty insulation around plumbing vents, electrical boxes, and the tops of interior walls when you look in the attic.
What it costs in Benbrook
Top plate and penetration sealing in Benbrook runs $800-$2,000, with most homes under $1,500.
How we do it
We seal every top plate seam, wire chase, plumbing vent, and recessed can light housing with expanding foam, then verify the work with a thermal camera.
What Attic Air Sealing Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Attic floor air sealing | $1,000 - $2,500 |
| Top plate and penetration sealing | $800 - $2,000 |
| Can light and duct boot sealing | $400 - $1,200 |
| Attic hatch sealing | $150 - $500 |
Can air sealing replace insulation in a Benbrook home?
No, and it shouldn’t. Air sealing and insulation work together: sealing stops the air movement, insulation stops the heat transfer. In these older Benbrook homes with both problems, you need both solutions, and doing sealing first makes the insulation far more effective.
How much difference does attic air sealing actually make?
In blower door tests we’ve run on Benbrook ranch homes, sealing typically reduces air leakage by 20-40%. That translates directly into less AC runtime in July and fewer furnace cycles in January. Call (866) 751-4428 if you want to see your numbers.
Wall Insulation in Benbrook
Wall insulation in Benbrook is the sleeper upgrade most homeowners don’t think about until a January freeze or a July heat wave shows them exactly where the gaps are. Many 1960s and 1970s Benbrook homes have no wall insulation at all, or at most a thin batt that’s settled and separated from the framing over 50 years. Our Wall Insulation work focuses on getting material into those walls without tearing out drywall in the process.
Injection Foam Wall Insulation
Signs you need it
Your exterior walls feel cold or hot to the touch depending on the season, and the house loses temperature quickly after the HVAC cycles off.
What it costs in Benbrook
Injection foam wall insulation in Benbrook typically runs $3.50-$6.00 per square foot of wall area, with most ranch homes falling between $3,000 and $8,000.
How we do it
We drill small access holes through the exterior or interior, inject polyurethane foam that expands to fill the wall cavity, and patch the holes to match.
Drill & Fill Wall Insulation
Signs you need it
You can see daylight around exterior wall outlets, or you’ve noticed rooms on the west side of the house are 5-7 degrees warmer in summer.
What it costs in Benbrook
Drill and fill wall insulation in Benbrook runs $2.50-$4.50 per square foot of wall area, depending on whether we use cellulose or fiberglass.
How we do it
We drill from the exterior, blow loose-fill insulation into each wall cavity, and close the holes with color-matched plugs so the exterior looks untouched.
What Wall Insulation Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Injection foam wall insulation | $3,000 - $8,000 |
| Drill and fill wall insulation | $2,000 - $6,000 |
| Interior wall soundproofing | $1,500 - $4,000 |
| Exterior wall insulation (new construction) | $2,500 - $6,500 |
Can you insulate walls without removing drywall in Benbrook?
Yes, that’s exactly what injection foam and drill-and-fill methods do. We access the wall cavities from outside or through small interior holes, fill them, and patch everything back. Your drywall stays intact and you don’t move out during the work.
Do 1970s Benbrook homes have any wall insulation?
Some do, but it’s usually a thin R-11 batt that’s sagged inside the cavity. The exterior walls of most 1970s ranches here have substantial uninsulated voids. We can check with a thermal camera before recommending anything. Call (866) 751-4428.
Attic Cleaning & Rodent Proofing in Benbrook
Attic cleaning and rodent proofing in Benbrook is a direct response to what we actually see in these older homes: squirrels, rats, and raccoons moving through the same gaps the clay soil opened up decades ago, then nesting in the insulation. Once that happens, the attic isn’t just dirty; it’s a health issue. Our Attic Cleaning & Rodent Proofing work removes the mess and keeps the animals out for good.
Attic Cleanout
Signs you need it
You hear scratching above the ceiling at night, or you see rodent droppings around the attic access hatch.
What it costs in Benbrook
An attic cleanout in Benbrook typically runs $1,500-$4,000 depending on the size of the attic and the extent of the debris and nesting material.
How we do it
We remove all contaminated insulation, vacuum the surface debris, and haul everything away so the attic is completely empty before you decide what goes back in.
Rodent Proofing & Exclusion
Signs you need it
You’ve had animals in the attic before, or you’ve noticed gnaw marks around the roofline, vents, or where the garage meets the house.
What it costs in Benbrook
Rodent proofing and exclusion in Benbrook runs $800-$2,500, with most homes under $2,000 for sealing all entry points.
How we do it
We seal every entry point with steel mesh, metal flashing, and foam, focusing on the gaps where rooflines meet walls and where the clay soil has shifted framing.
What Attic Cleaning & Rodent Proofing Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Attic cleanout | $1,500 - $4,000 |
| Rodent proofing and exclusion | $800 - $2,500 |
| Attic sanitizing and decontamination | $600 - $1,800 |
| Attic restoration (cleaning + new insulation) | $3,500 - $8,000 |
How do I know if I have rodents in my Benbrook attic?
Listen for scratching in the early morning or evening, check for droppings near the access hatch, and look for gnawed wires or torn insulation. If you see any of those, we’ll inspect the attic and tell you exactly what’s living up there. Call (866) 751-4428.
Do you remove the animals too?
We focus on the attic itself: removing contaminated insulation, sanitizing, and sealing entry points so animals can’t get back in. For live animal trapping, we’ll point you to a licensed wildlife removal contractor in Benbrook, then handle the cleanup after they’re gone.
Home Energy Audit in Benbrook
A home energy audit in Benbrook finds the specific problems that make a 1970s ranch house expensive to heat and cool. In these homes, the issues are almost never just one thing: it’s usually a combination of thin attic insulation, air leaks at the top plates, and an HVAC system that was retrofitted into the attic decades ago. Our Home Energy Audit gives you a complete picture before you spend any money on fixes.
Blower Door Test
Signs you need it
You want to know exactly how leaky your Benbrook home is, not just a general guess, before deciding where to spend your insulation budget.
What it costs in Benbrook
A blower door test in Benbrook typically runs $250-$500 as part of a full home energy audit.
How we do it
We mount a calibrated fan in an exterior door, depressurize the house, and measure the exact airflow that leaks in through every gap and crack.
Thermal Imaging Inspection
Signs you need it
Certain rooms in your Benbrook home stay hot or cold regardless of the thermostat, and you want to see where the envelope is failing.
What it costs in Benbrook
A thermal imaging inspection in Benbrook runs $200-$450 when done as part of a home energy audit.
How we do it
We scan every wall and ceiling with an infrared camera to pinpoint missing insulation, air leaks, and thermal bridging that you can’t see otherwise.
What Home Energy Audit Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Full home energy audit | $400 - $800 |
| Blower door test | $250 - $500 |
| Thermal imaging inspection | $200 - $450 |
| Insulation inspection | $150 - $350 |
Is a home energy audit worth it before insulating?
Yes, because it tells you where the problems actually are. In Benbrook homes with multiple issues, an audit prevents you from spending thousands on insulation that doesn’t address the real leak. It’s the cheapest money you’ll spend on the whole project.
Do you test for air leaks in the attic specifically?
We do, with both the blower door and the thermal camera working together. The blower door depressurizes the house and makes attic leaks obvious, while the thermal camera shows the temperature differences those leaks cause. Call (866) 751-4428 for a free second opinion on any written estimate you’ve received.
Brands We Service in Benbrook
We install and service insulation from the manufacturers Benbrook homeowners actually ask for: Owens Corning, Icynene, and Demilec are what we stock and install most often. Parts and material are available quickly through our Dallas-Fort Worth supply chain, so a Benbrook job rarely waits on anything. Not sure which product fits your house? Check our brands page for a plain-English breakdown.
Pricing for Insulation in Benbrook, TX
| Service | Typical range in Benbrook |
|---|---|
| Crawl space vapor barrier | $1,200 - $3,500 |
| Full crawl space encapsulation | $5,000 - $12,000 |
| Open-cell spray foam attic | $3,000 - $7,000 |
| Closed-cell rim joist spray foam | $1,500 - $4,000 |
| Blown-in cellulose attic | $1,500 - $3,000 |
| Attic radiant barrier | $1,200 - $3,000 |
| Attic insulation removal | $1,500 - $3,000 |
| Attic air sealing | $1,000 - $2,500 |
| Injection foam wall insulation | $3,000 - $8,000 |
| Attic cleanout and rodent proofing | $1,500 - $4,000 |
| Full home energy audit | $400 - $800 |
What pushes prices up in Benbrook specifically is attic access: when HVAC equipment from the 1990s fills the attic cavity, our crews need more time to work around it, and tighter crawl spaces on those older split-levels cost more to encapsulate than open crawl spaces. Every quote is upfront: you’ll see the number before we start, not after.
Neighborhoods We Serve in Benbrook
We work throughout Benbrook and most of the surrounding communities, including several neighborhoods where the housing stock shares the same 1960s-1980s construction and the same climate challenges. A technician is usually on site the same day you call, and we schedule around your work hours when it helps.
- Westpark
- Timber Creek
- Rolling Hills
- Whitestone
- Mary’s Creek
Service Area - Cities Near Benbrook
Walt’s Insulation is based in the Dallas-Fort Worth metro and serves Benbrook with local crews and a live-answer phone line. If you’re in one of the nearby cities we cover, check the relevant page: San Antonio, TX, Houston, TX, Spring, TX, or The Woodlands, TX. Same owner, same crews, same guarantee.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in Benbrook
How fast can you get to a Benbrook home?
Frequently Asked Questions
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 30-60 min.
- 4You approve before work beginsNothing starts until you say go.
What Benbrook Customers Say
"Air sealing first, then blown-in over the top. He found a bathroom fan venting straight into the attic and fixed that too. Written price before they started, same price when they finished."
- Arjun Mehta"Spray foam in the garage ceiling under the bonus room. That room used to be unusable in summer. Walt talked me out of foaming the whole attic because it did not need it - saved me a couple thousand and I trust him more for it."
- Bud Larkin"Crawl space was wet every spring. They laid the heavy liner, sealed the vents, and put a dehumidifier down there. Floors are warm and the moisture meter he left reads fine now. He still answers when I text him a reading."
- Devon Pierce