Icynene Blown-In Insulation Nationwide | Walt’s Insulation

Icynene Blown-In Insulation in San Antonio: What to Know First

Icynene blown-in insulation repair and installation in San Antonio typically runs $1.80 to $3.60 per square foot depending on whether we’re topping up existing Icynene, doing a full removal and reinstall, or correcting a failed section. Most Icynene jobs are finished in one day, and we give you an upfront quote before any work starts. We’re an independent Icynene service provider, not a factory authorized dealer, which means we tell you what’s actually wrong with your insulation and fix it without pushing a brand agenda.

Call (866) 751-4428

This page is for San Antonio homeowners who already have Icynene insulation, or got sold an Icynene product somewhere down the line, and want straight answers about why it’s not performing the way the sales pitch promised. Call (866) 751-4428 and you’ll get a live person, not a voicemail.

How Icynene Products Fail - and How We Fix Them

• Icynene Classic open-cell shrinkage and gaps. The original Classic formula, installed in hundreds of San Antonio homes from the early 2000s through about 2010, is known to pull back from studs and rafters as it ages. That shrinkage leaves air channels along the framing, and in a Bexar County attic where July temperatures push 140 degrees, those gaps move a lot of hot air. We inspect the entire envelope, identify the separated sections, and either dense-pack around the failed areas with blown-in fiberglass or remove and redo the affected zones entirely.
• Icynene ProSeal settling in wall cavities. ProSeal was marketed as a closed-cell product for walls and cathedral ceilings, but we’ve pulled enough drywall off San Antonio homes to see where it didn’t cure properly and settled into a hard mass at the bottom of the cavity. That leaves the top half of the wall uninsulated. The fix is usually removal of the settled material and a dense-pack blown-in insulation retrofill, which we do through small access holes rather than tearing out entire walls.
• Moisture-trapping in open-cell Icynene installed against unvented roofs. Open-cell Icynene against the underside of a roof deck without proper ventilation gets damp, and damp open-cell foam loses its R-value and can hold water against the sheathing. This is a known issue in San Antonio’s humid climate, not a defect in every case, but the installation method matters. We check the roof assembly for airflow, dry it out if needed, and often switch the homeowner to a ventilated setup with blown-in insulation on the attic floor instead.
• Rodent and pest tunneling through Icynene Light. Icynene Light, the lower-density open-cell product, is easy for rats and squirrels to chew through once they get into an attic. We see this constantly in older San Antonio neighborhoods like Alamo Heights and Monte Vista, where mature trees give rodents a highway onto the roof. We remove contaminated foam, seal entry points, and re-insulate with a pest-resistant blown-in material that doesn’t give them the same bedding opportunity.
• Improperly mixed or off-ratio Icynene in retrofit jobs. Spray foam is only as good as the installer’s equipment and the mix ratio in the gun. When the A and B sides aren’t balanced, the foam can stay tacky, smell off, or crumble. We’ve corrected plenty of these jobs in San Antonio homes where the original installer was a franchise crew rushing through a subdivision. Our approach is systemic: identify the off-ratio areas, remove the failed material, and rebuild the thermal boundary correctly with blown-in insulation that doesn’t depend on a chemical reaction gone wrong.

Our Icynene Blown-In Insulation Process

1. 1
   We inspect the entire assembly first. We look at what type of Icynene you have, where it’s failing, and what the attic or wall conditions actually are. No guesswork.
2. 2
   We explain what we found in plain language. You’ll know what’s wrong, what your options are, and what it costs before we touch anything.
3. 3
   We remove only what needs to go. If sections of Icynene are still holding up fine, we leave them alone. We don’t sell you a full removal unless it’s warranted.
4. 4
   We install blown-in insulation matched to your San Antonio climate. Depending on the cavity and the existing material, that’s blown-in cellulose, blown-in fiberglass, or dense-pack wall insulation. The R-value gets calculated for our heat and humidity, not a national average.
5. 5
   We verify air sealing. Blown-in insulation without proper air sealing just filters hot air through the fluff. We seal penetrations, top plates, and bypasses so the insulation can do its job.
6. 6
   We clean up and walk you through it. You see the finished attic before we leave. And every job carries our lifetime Done Right Promise: if it’s not done right, we make it right.

What Icynene Blown-In Insulation Costs in San Antonio

Here’s what we typically see in the San Antonio market for Icynene-related blown-in insulation work:

• Blown-in top-up over existing attic insulation: $950 to $2,200 for a typical 1,500 to 2,500 square foot home, depending on target R-value (R-38 to R-49 is what the San Antonio climate calls for).
• Dense-pack wall insulation where Icynene has settled or failed: $2.50 to $4.00 per square foot of wall area. That includes drilling access holes, filling, and patching.
• Full Icynene removal and blown-in replacement in an attic: $4,800 to $12,000 depending on attic size, contamination (rodent damage, moisture), and accessibility.

The biggest price drivers are attic accessibility, how much of the existing Icynene has to come out, and whether there’s rodent or moisture damage to remediate first. You’ll get a written, upfront quote before any work begins. Estimates are free, and we don’t charge a trip fee inside our service county. Call (866) 751-4428 and we’ll schedule a time that works for you.

Why San Antonio Homeowners Call Walt’s Insulation for Icynene Work

Walt Brenner started this company in 2000, after years of watching San Antonio homeowners get sold insulation that wasn’t right for our climate. We’re not a franchise and we’re not an 800 number. We’re the one down the road, with a published address and a license number you can actually look up. When you call, a live person answers, 24/7. No answering service, no voicemail.

Our techs are background-checked, uniformed, and they’ve worked on Icynene jobs across San Antonio long enough to know the difference between a product failure and an installation failure. And we don’t just work with one brand. Alongside Icynene, we install Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Demilec, and GreenFiber products, plus Reflectix for radiant barrier applications. When one manufacturer’s product isn’t the right fit for your house, we tell you and use what is. That’s the whole point of being independent.

FAQs